Products

  • MF mechanical connector shear bolt connector

    MF mechanical connector shear bolt connector

    MF connectors consist of a tin-plated body,shear bolt heads and inserts for small conductor sizes.
    Made of High-strength special aluminum alloy, these contact bolts are double shear bolt heads with hexagon heads. The bolts are treated with a highly lubricating agent. Contact bolts are irremovable once their heads have been sheared off. The lug body is made of a high-tensile, tin-plated aluminium alloy. The internal surface of the conductor holes are grooved.

  • stepless shear bolt connectors

    stepless shear bolt connectors

    Terminals, connectors and cable lugs using screw technology have been on the advance for years, and with good reason. The special design feature of the  shear bolt connectors is that there are no predetermined break points in the thread. This provides for optimal load bearing capacity for each range of cross sections. The bolt always breaks at the surface of the clamp body, so there are no protrusions and nothing has to be filed down to make the sleeve fit. Fitting requires a simple tool – literally with a flick of the wrist. Offering a large clamping range,  shear bolt connectors feature a compact design with rounded edges and flat transitions suitable for slide-on and shrink sleeves

  • Preformed dead end guy grip

    Preformed dead end guy grip

    Material
    Ground wire for steel conductor; wire clamp is used for galvanized steel.
    Aluminum-clad steel, good conductor ACSR, wire clamp is used for aluminum-clad steel wir

  • Preformed guy grip with dead end clamp

    Preformed guy grip with dead end clamp

    Component

    Inner armor rods, outer armor rods, thimble, U-shaped hanging loop, extension loop, bolt, nut, etc.

    Characteristic

    1. Stress is distributed equally, without stress focus. It can protect optical cables very well.

    2. Under the condition of not exceeding the intensity of cable’s side pressure, it has higher grip power for the cable, and can support higher tensile force.

    3. The grip power for the cable is not less than 95% of rating’s pulling resisting intensity of the optical cable, completely satisfying the needs of setting up the cable.

    Preformed line material: Aluminum clad steel wire

  • Preformed guy grip with dead end clamp

    Preformed guy grip with dead end clamp

    The preformed tension set is widely used for the installation of bare conductors or overhead insulated conductors for transmission and distribution lines, the reliability and economic performance of the product is better than the bolt type and hydraulic type tension clamp that widely used in the current circuit.
    Innovative structure and precision design, so that the preformed tension set has a reliable performance and it is usually made of aluminum clad steel, galvanized steel wire and other materials.

    Tension Clamps are designed to connect ADSS cables and poles/towers . Armor rods can provide protection and cushioning to the ADSS cables. The special design of Preformed rods makes ensure that Tension Clamps can’t cause undue stress to the ADSS cables, so as to ensure the normal lifetime of cables  system.

    Preformed line material:  Aluminum clad steel wire or galvanized steel wire.

  • Preformed guy grip

    Preformed guy grip

    Dead end preformed is widely used for the installation of bare conductors or overhead insulated conductors for transmission and distribution lines, the reliability and economic performance of the product is better than the bolt type and hydraulic type tension clamp that widely used in the current circuit. This unique, one-piece dead-end is neat in appearance and free from bolts or high-stress holding devices. It can be made of galvanized steel or aluminium clad steel.

    Preformed line material: Aluminum clad steel wire

  • Automatic Splice

    Automatic Splice

    CORROSION RESISTANT SPLICE/AUTOMATIC SPLICE CONNECTOR

    Aluminum Automatic Splice cable connector is suitable for maintenance and repair of broken line or new line.A tension-dependent device in which the line is installed with at least 10% tension of the rated strength of the wire to ensure a reliable electrical connection, and the current is transmitted to the other end through the wire clip of the wire. Taper type automatic quick connector (full tension automatic connector)


  • Stainless steel tape coil

    Stainless steel tape coil

    Material:Stainless steel 201/304/316 ,All length are available upon your request

  • Steel Guy Wire

    Steel Guy Wire

    ◆ The GUY-LINK is used primarily by telephone and electric utilities to terminate strand or rod at the pole top and at the anchor eye. For Suspension Strand, Guy Strand and Static Wire. Used to terminate aerial support strand messenger, and at the top and bottom ends of down guys.
    ◆For splicing applications with overhead or support guy wires
    • Automatic splices are designed for use on
    High Strength (HS), Common (Com), Siemens-Martin (SM), Utilities
    (Util) and Bell System strand
    • Automatic splices are designed for use on
    all guy wire types listed above, plus Extra High Strength (EHS) and
    Alumoweld (AW)
    • All GLS automatic splices will hold a minimum of 90% of the guy
    wire rated breaking strength
    Material: Shell – High Strength Aluminum Alloy
    Jaws – Plated Steel

  • DT cable lug/ SC Terminals Connecting Tube

    DT cable lug/ SC Terminals Connecting Tube

    Product Description

    DT  is applicable to the connections of wires in distribution equipment power supply cable with electronic apparatus. It is made of T2 cooper tube by die cast and coated tin.
    SC(JGY) Copper Terminals Connecting Tube
    Features:
    JGY Copper Crimp Lug is made of with higher 99.9 percent pure copper tube T2 and coated with tin. Working temperature -55℃-150℃.

    Application:
    JGY Copper Crimp Lugs are suitable for the connection of copper conductors(section 1.5-1000mm2) in power cable with electronic equipment.

  • Aluminum tension clamp

    Aluminum tension clamp

    For optical fiber cables type ADSS, Automatic conical tightening. Opening bail easy to be installed.
    All the parts secured together.

  • hot line clamp

    hot line clamp

    • Eyebolt coated with high temperaturegrease, assuring easy turning in all weather conditions
    • Full-current rated connector for use as an in-line jumper OR device tap.
    • An increased conductive path and surface contact area between the main and
      tap line increases current ampacity rating.
    • Typical applications are transformers, lightning arrestors, cutouts, etc.
    • Can be installed directly to the main line. No need for using a bail or stirrup.
    • Incorporates the use of a Stainless Steel eye bolt for increased strength and corrosion resistance.
    • Constructed of 6061-T6 structural aluminum alloy to provide high strength and conductivity.
    • Exclusive high-conductivity grit type corrosion inhibitor is factory applied for ease of installation and longevity while the connector is in service.
    • Remains permanently locked through fault current or power surges.
    • Horizontal wedge action prevents the conductor form “sticking” during the removal process.
    • Easy to remove without damaging cable.